|
|
|
|
|
|
|
|
|
|
|
|
|
|
This sliding screen door roller assembly insert has a high density polyethylene frame with an adjustable high density polyethylene inner housing and high density polyethylene roller. The assembly inserts into the bottom or top of the sliding screen door by snapping it into place. The roller housing adjusts to the correct position needed. This style is found on Columbia sliding screen doors but is also used by very many other screen door manufacturers.
|
This high density polyethylene roller assembly was used on HiLite doors. It is a high density polyethylene bracket with a spring loaded 9/16 in Dia flat edged high density polyethylene roller inside. It fits into a rectangle slot in the bottom of the door and is held in by the included screw.
|
This Arcadia style roller assembly was used by Arcadia doors as well as many other patio door manufacturers. This is also currently a very popular design amongst patio door manufacturers in today's market place. It has a wire tension spring and comes with a 1 in high density polyethylene roller and fits onto the B 569 corner insert. It is often used on the top as well as the bottom of the sliding screen door.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This is a roller is used on bottom mount installations. It is a 1 in steel ball bearing roller with a 1/4 in axle hole. The 1/4-20 x 3/4 in carriage bolt inserts through the screen door frame and through the roller and is then secured in the bottom rail with a nut.
|
This sliding screen door roller assembly insert has a thinner high density polyethylene frame than the B 646. It has an adjustable high density polyethylene inner housing and high density polyethylene roller. The assembly inserts into the bottom or top of the sliding screen door using the included screws. The roller adjusts to the correct position needed. This style is found on Columbia sliding screen doors but is also used on very many other screen door manufacturers. Please note dimensions and design when comparing with old roller.
|
This rocker style spring tension roller assembly is used on International doors. It was used on International Series 900, 925, 950 and newer. The body is stamped aluminum with a tension spring attached. It has a 1 in high density polyethylene center grooved roller.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This insert style sliding screen door assembly has a high density polyethylene housing with a high density polyethylene roller insert. It is used on the Academy Uni-Fit screen doors. The roller is a 1 in high density polyethylene roller and is used on the top or the bottom. Easy to install by inserting into the open U shaped frame and inserting the screw.
|
This roller assembly with M shaped tension spring with a 1 in high density polyethylene ball bearing roller is used by several patio door manufacturers. The heat-treated tension spring is 2-5/16 in L and shaped like an M giving it the tension needed by the screen door to slide properly.
|
This center grooved sliding screen door tension roller is used by many patio door manufacturers. Used on the bottom as well as the top of the sliding screen door. The roller is a 1 in steel ball bearing roller. The tension spring 2-1/2 in L and is a heat-treated high tension steel spring.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This is a tension spring roller assembly with a V shaped spring design is used by several patio door manufacturers. The roller is a 1 in steel ball bearing roller with a heat-treated steel tension spring that is V shaped. The 2 in L V shaped flat spring inserts into the screen frame giving tension required as the door slides back and forth.
|
This sliding screen door top roller guide was used on HiLite Doors. The high density polyethylene body installs into the top of the screen door frame and is held in place by the included screw. The guide roller is a 11/16 in oval ball bearing high density polyethylene roller.
|
This high tension steel spring roller assembly fits onto the Columbia Uni-Fit Series door. This roller assembly has a 1 in steel ball bearing roller mounted in the housing. The end of the flat steel spring inserts into a slot within the screen door frame while the flat tabs extending in front of the roller restrict the roller from retracting too far into the door frame as it rolls.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This top hung roller assembly is used on Fullview doors as well as other patio door manufacturer's doors. The bracket is a flat stamped steel bracket with slotted mounting holes that allow it to be adjusted o the correct height when re-installing the screen door onto the upper track. The roller is a 1 in steel ball bearing center grooved roller.
|
This Arcadia style roller assembly is used by Arcadia doors as well as many other patio door manufacturers. This is also currently a very popular design amongst patio door manufacturers in today's market place. It has a wire tension spring and comes with a 1 in steel ball bearing roller and fits onto the B 569 corner insert. It is often used on the top as well as the bottom of the sliding screen door.
|
This sliding screen door roller assembly insert has a high density polyethylene frame with an adjustable high density polyethylene inner housing and steel ball bearing roller. The assembly inserts into the bottom or top of the sliding screen door by snapping it into place. The roller housing adjusts to the correct position needed. This style is found on Columbia sliding screen doors but is also used by very many other screen door manufacturers. Please note dimensions and design when comparing with old roller.1 in steel ball bearing roller.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This sliding screen door roller assembly insert has an aluminum frame with a high density polyethylene inner housing and steel ball bearing roller. The assembly inserts into the bottom or top of the sliding screen door with the included screws. The roller housing adjusts up and down to the correct position needed. This style is often on Columbia sliding screen doors but is also used by very many other screen door manufacturers. Please note dimensions and design when comparing with old roller.
|
This sliding screen door roller assembly insert has an high density polyethylene frame with an adjustable high density polyethylene inner housing and high density polyethylene ball bearing roller. The assembly inserts into the bottom or top of the sliding screen door using the included screws. The roller adjusts to the correct position needed. This style is found on Columbia sliding screen doors but is also used on very many other screen door manufacturers. Note dimensions and design when comparing with the roller assembly to be replaced.
|
This stainless steel roller assembly with M shaped tension spring with a 1 in H density polyethylene roller is used by several patio door manufacturers. The heat-treated stainless steel tension spring is 2-5/16 in L and shaped like a M giving it the tension needed by the screen door to slide properly.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This sliding screen door roller assembly fits the Andersen Narroline, Frenchwood and Perma-Shield doors. The roller assembly snaps into place with the adjustment stem being accessible on the edge of the door frame. The housing is high density polyethylene with a grooved 1-1/4 in Dia high density polyethylene roller.
|
This steel housing and spring-loaded arm with the 1 in steel ball bearing roller attached is used by Bay-Mills as well as several patio door manufacturers. The roller arm is spring-loaded and adjusted by the adjustment sleeve and screw on top.
|
|
|
